How To Clean The Whirlpool Cabrio Washer?

Helen Skeates
Helen Skeates
14 min read

As a top-loading washing machine with Whirlpool’s 6th Sense Technology, the Cabrio is designed to deliver optimal performance with every load. Because of the high frequency with which your Whirlpool Cabrio washing machine is used, it is susceptible to detergent spillage and fabric softener residue accumulation. Water, soiled clothes, or mildew growth can cause the machine’s inside to become musty or dirty. Keep your Whirlpool Cabrio washer clean by cleaning it once a month.

Steps To Clean The Whirlpool Cabrio Washer

The washing machine’s rinse cycle may not be enough to remove all traces of dirt and debris. In the course of cleaning your clothes, the bacteria in your washing machine spreads about and may cause respiratory difficulties, unpleasant odours, and dark spots. To prevent this from happening again, you must thoroughly clean your washing machine. For added security, you can also schedule the clean-up so you won’t forget. The correct cleaning of your washer is essential if you plan to use it today or tomorrow. We used to think that rinsing it after use was sufficient, but unfortunately, that isn’t the case at all. So, here are the procedures to cleaning the Whirlpool Cabrio washing machine:

Step #1. Empty the drum

Open your washer’s door or lid. If you’ve already put your clothing in the washing, take them out first or remove them from the machine. It’s best not to put anything in the drum because it could produce an unpleasant stench.

Clean Whirlpool Cabrio HE Washer Using Natural Ingredients - YouTube

Step #2. Prepare your washer cleaner

There are a variety of powders and pills that you can use to clean your washing machine. It’s possible to look at them online or find a nearby retailer to purchase them. In the washing machine, it is more effective than normal detergents.

Step #3. Place your washer cleaner

Fill the washer’s basket or drum with your washer cleaner. When loading a cycle, do not put the washer cleaner in your detergent dispenser, since it may have different effects on your garments when the cycle is over. When using a washer cleaner, it is not advisable to add additional chemicals.

Step #4. Begin the cycle

Turn on your washing machine and close the door or lid. Next, press the Clean Washer button on your Cabrio washer. At least three seconds after that, push and hold the Start/Pause button.

Step #5. After the cycle

Rinse and spin the washer after the cycle is complete. The cleaner will be flushed. It is advisable to open the lid and leave it to dry the washer and prevent odor-causing residue from building up. Finally, it’s all done and done. If your washer doesn’t have a clean washer button, you can clean your washer by using hot water and a cup of chlorine to your washer. Afterwards, run a standard cycle and then rinse it. Open the door or lid of your washing machine to dry it out.

The Importance of Cleaning Your Washer

The buildup of sticky, detergent residues, bacteria, and molds from your clothes will begin to occur when you wash your clothes many times a week. You need to clean your washer for a variety of reasons, and I’ve highlighted three of the most important ones below. As a bonus, this guide will help you appreciate the value of washing your clothes by hand.

#1. Respiratory problems

However, this is a common occurrence. Washing your garments in the washing machine gathers and may spread bacteria rather than merely eliminating them. For those who are allergic to mould, exposure to the mold may cause an allergic reaction or asthma symptoms.

#2. Black residue

This black residue is from the soap or detergent residue that build-up in the lid or the washer’s door. It’s also been found inside a drum or a basket on occasion. It’s possible that this residue will adhere to your clothing and leave you with dark stains.

#3. Black spots in clothes

Limescale can also leave black stains on your clothes when you wash them. There is a white chalky residue in the machine caused by limescale. This will also lead to malfunctions in some elements of the washer.

#4. Bothersome odor

The presence of a foul stench can be a sign that something is amiss. The same germs and molds are to blame for all of the annoying, nasty, and irritating scents. Even if you wash your garments, the aroma will remain. The odors will be removed by cleaning the washer, and this will have no effect on the smell of the garments you wash afterwards. Learn the causes of washing odors and how to avoid and remove them.

How Do I Reset My Whirlpool Washing Machine?

Steps to Reset a Whirlpool Washing Machine

Resetting your Whirlpool washing machine is as simple as following these steps:

  • Shut off the washing machine
  • Set the mode dial to NORMAL.
  • Once you’ve turned the dial a full turn to the left, turn it back to the right and do the same thing again.

How to Confirm You Have Reset Your Whirlpool Washing Machine

Then press the START button to begin the process. Ensure that all of the cycle indicators are lit. If this is the case, you must hit START/STOP once. Turn the dial until the RINSE, WASH, and STOP lights are all lit up. After that, switch off and unplug your washer for ten seconds. When you switch it back on, it should have been reactivated.

You can do a test load without any garments to confirm that the reset has been successfully completed. If it didn’t work out, you can attempt the same thing again. If that doesn’t work, you can try the Cabrio reset method as a last resort.

Whirlpool Cabrio Platinum WTW8800YW 4.6 cu. ft. White Top Loading Washing Machine Review - Reviewed

Try the Cabrio Reset Procedure

Attempt the Cabrio reset process if the problem with your washer persists. Any button you see on your display pad should be pressed. Clearing the error code will do this. You may also choose to pause or cancel the recording by using the PAUSE/CANCEL button. Press START to begin a cycle after making your selection.

Afterwards, disconnect the Cabrio from power if the problem or error reappears. Five minutes is plenty of time to give it a try. Select a new cycle and hit the START button. To check that the reset operation was successful, run the load empty. This should have worked, but if it didn’t, you can try again.

Washer Making Unusual Noises

The washing machine is making a lot of noise.

  • The load is probably imbalanced if the noise is a loud thumping. Restart the washing machine and disperse the wet laundry. Washer overload may necessitate removing some items.
  • The washer is not leveled or anchored on the floor if it makes a clanking noise. Correcting this as soon as possible will help avoid further damage.
  • If the washer is making a loud whine, it’s time to investigate more. On the Whirlpool website, you’ll find a service manual or schematic showing how the washer works inside. Washer Pulley Nut: Remove outer housing and inspect pulley nut. The nut may need to be tightened. If that doesn’t work, you’ll have to get new bearings.

Washer Won’t Start

There is no power to the start button on the panel, but all other lights are on.

  • To find out what’s wrong, remove the control panel. You’ll need a repair manual to assist you remove the control panel.
  • Make sure nothing is broken or missing. There are occasions when the start button does not work because a small piece of plastic has broken off.
  • Use a voltage meter to check all of the wiring. The complete control panel must be replaced if the timer, main controller, or CCU malfunctions.

Lid Lock Issues

Cycles will not commence if the washer’s lid locks but then unlocks.

    • If the lid latch/switch is unclean and does not make good contact with the washer’s control panel, the machine will not begin a cycle. You can use isopropyl rubbing alcohol to clean your skin. Clean the washer’s lid and all of its contact points.
    • To reset the washer’s control panel, disconnect it. Check to see whether the problem goes away after reconnecting the washer.
    • You should run a diagnostic test if the door sounds as if it is closing but does not. There could be a more serious issue at hand. What you need to do is:
    • The diagnostic mode is successfully entered when all console indications are illuminated for 5 seconds and the two-digit display indicating 88 appears in the Estimated Time Remaining field.
  • Press/hold and release may not have been accomplished in time if indicators do not show up as indicated if they do not work. To be sure that this wasn’t the source of the problem, try it again with a different button.
  • Next, the application looks for any previously saved error codes. Once you’ve completed the diagnostic test, you can use the error code displayed to determine what repairs are necessary.

Deciphering the LD Error Code

When the spin cycle is complete, an LD Error Code shows.

ERROR CODE “LD” stands for “Long Drain.” When the washer runs out of water, it has to stop because it takes too long to drain. The most common reason for this is a clogged drain or anything blocking the pump.

  • Clean out any lint or obstruction (coin, small button) that is clogging the pump filter.
  • Make sure that the pump filter is clear of any lint or obstructions (coin, small button).
  • A new water pump may be necessary if these measures fail to fix the problem.

Washer Leaves Deposits on Dark Clothes

No matter what detergent you use, your washer leaves white deposits on your clothes.

  • If the deposits appear exclusively in the winter months, it may be that a powdered detergent is not entirely dissolving in the extremely cold water. Replace your cold water cycle with a warm water one.
  • It’s time to clean your washer if you’re seeing a lot of buildup. There isn’t as much water in high-efficiency washers as in normal washers, which makes it harder to remove detergent and soil residue from the washer. In the shower, you can think of it as soap residue. To prevent the buildup from reappearing on your clothes, give your washer a good cleaning.

Washer Has a Burned Plastic Odor

Burning plastic or rubber smells are coming from the washer.

  • You can’t avoid the smell of burning rubber. Unplug the washing machine and remove the outside casing to inspect.
  • Keep an eye out for any fading. It’s possible that the rubber drive belt is causing the issue. A burning “rubber” scent might be caused by the belt slipping, stretching, or breaking. Belt replacement is necessary.
  • It’s most likely an electrical issue with the motor, gearbox, or control panel if the belt is fine. As a result, this is a considerably more serious issue, requiring the replacement of the damaged components.
  • To avoid a fire hazard, do not operate the washer until repairs have been performed.

Whirlpool Cabrio 4-cu ft High Efficiency Impeller Top-Load Washer (White) in the Top-Load Washers department at Lowes.com

Rust Spots on Washer Lid

The Cabrio Washer Lid has rust stains on the inside.

  • In the long run, rust stains will never disappear. Only if they are repaired can rust stains be transferred to the laundry. To begin, use a paste of baking soda and distilled white vinegar or lemon juice to remove as much of the rust development as possible. To form a thick paste, combine 1/4 cup baking soda with just enough vinegar or lemon juice.
  • After applying the paste to the corroded area, use a soft cloth to remove any rust residue. Do this a few times, washing with clear water after each procedure.
  • Repair the rusted sections with an appliance paint, following the package guidelines, once you’ve removed all of the loose rust.

It’s a Wrap!

There are many different ways to clean the Cabrio washer, so maybe this article has given you some fresh ideas. The capability and performance of your washer are directly influenced by how clean it is. In order to save money on repairs and maintenance, you should inspect and clean your washer at least once a month. Learn how to remove mold from the gasket on a front-loading washer and how to clean the drain hoses on a washer.

Helen Skeates

Helen Skeates

Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book. It has survived not only five centuries, but also the leap into electronic typesetting, remaining essentially unchanged. It was popularised in the 1960s with the release of Letraset sheets containing Lorem Ipsum passages, and more recently with desktop publishing software like Aldus PageMaker including versions of Lorem Ipsum.