How To Replace Motor Coupling On Kenmore Washer?

Helen Skeates
Helen Skeates
26 min read

How do you replace a Kenmore washer’s motor coupling? You should follow these ten simple actions. Your washer doesn’t spin when you switch it on on a set day each week for laundry. And now you’re scratching your head, trying to figure out what could have caused it. Yes, I’m searching for a simple yet effective answer. Having a problem with your Kenmore washer’s motor coupling? Don’t worry, we’ve got you covered.

If your washing machine is running but not spinning, the problem may be caused by a faulty motor coupler. The motor coupler, which connects the motor to the gear case, is essential to the washer’s general operation.

Overloading the washer, putting in less water than necessary, and a worn-out motor coupler are a few of the possible causes of a malfunctioning motor coupler. In this guide, you’ll learn how to replace a faulty Kenmore motor coupler. Let’s get started on this article, shall we?

Steps To Replace Motor Coupling On Kenmore Washer

The motor coupler on a Kenmore washer can be simply replaced if the methods listed below are followed to the letter. Don’t skip a step and try to fix the washer at home if possible. Before you do anything else, get the following resources:

  • Hammer
  • Screwdriver
  • Gloves
  • Set of spanners

In order to replace a Kenmore washer’s motor coupling, below are the necessary steps:

Step #1.  Turn off the washer

Make sure the appliance is turned off before you begin the operation. Never attempt to fix a device without first disconnecting it from the power source. It will keep you from suffering life-threatening injuries.

How to replace the motor coupler on a top-load washer | Repair guide

Step #2. Remove water from the washer

You are ready to begin the repair work, but hold on a second; you have not yet removed any water from the washer? It’s critical to drain the washer completely of all water. You will be unable to carry out your strategy if this is not the case. After you’ve cleaned out the washer, you’re free to continue working as usual.

Step #3. Pull the washer out in a leaning position against the wall

Setting a washer in this position will aid in the repair.

Step #4.  Separate the control panel from the washer

Washer controls are found on the control panel, which is where the buttons are located. Make a search for screws that hold the control panel to the washer. The screws might be located on either side of the washer, or even behind it. Using a screwdriver, begin loosening all screws on the control panel until it is swiftly removed from the washer. To separate them, use a small amount of force.

Step #5.  Move the cabinet forward

You’ll need to pull the washer’s cover forward and put it away once you remove the control panel.

Step #6. Find the motor

Locate the washer’s motor if you can. The machine’s motor may be found at the machine’s base. The water pump should be ignored before looking for the motor’s placement. Then, remove the pump from the motor with a screwdriver.

Step #7. Pull the motor out

Before removing the motor, you must first remove the cables that connect it. To remove the remaining screws or clips, you’ll need a screwdriver. If the motor is too heavy for you to lift, you may want to enlist the aid of a friend.

Step #8. Install new coupling

Disconnect the motor’s drive shaft and remove the worn-out or broken coupler. Then, set the new coupler in its position and make sure it’s snugly in place.

Step #9. Place the motor back

Once the coupling is in place, use an isolator to arrange the loss projections on the outer surface of the coupling. Make sure the motor is in the correct place. Adjust the motor and plug in the wiring harness after reinstalling the screws and clips. Reconnect the water pump to the engine.

Step #10. Restart the washing machine

Replace the machine’s cover and panel cover by clasping them in the opposite direction that you removed them. Next, start up the washing machine and have a great day doing laundry. It’s good to know how to reset my washing machine, I guess.

Top 5 Excellent Kenmore Motor Coupler

On the basis of quality, these five Kenmore motor couplers are among the best available. So that you may see:

  1. This motor connection kit, part number 285753A, is designed to work with the Kenmore washer.
  2. It’s a heavy-duty replacement for your Kenmore washer washing machine’s part number 62672;
  3. The metal-reinforced core of part 285753A makes it ideal for use in a Whirlpool washer.
  4. For use with part number AP3963893 PS1485646, look no further than part number 285753.
  5. The metal-reinforced core of Marks 285753A makes it appropriate for your Whirlpool and Kenmore washers.

Preventive Measures

This is a simple operation, but it’s important to take precautions. Make sure you follow the directions exactly. The repair process should not be started unless all of the processes have been thoroughly explained to you. Make sure you’re safe with power tools. As a final point, take care of yourself and your loved ones’ well-being.

How to Replace the Drive Coupler on a Whirlpool Washer

Three rubber and plastic parts make up the drive coupling in your Whirlpool washer. They are attached to the transmission and the motor shaft. After a while, a clunking noise can be heard when the coupler or rubber isolator plate wears out, causing the washer to stop working. Before changing the drive coupler, you must first remove the washer’s cabinet.

  1. Remove the power cord from your Whirlpool washing machine. Disconnect the supply lines at the back of the appliance and turn off the water supply.
  2. To conduct the repair, you will need to disassemble your washing machine. The disassembly instructions for your specific model of Whirlpool top-load washer cabinet can be found under Resources.
  3. The white water pump is located beneath the washtub. To remove the pump, pull the retaining clips out with a flathead screwdriver. Remove the pump from the motor shaft of the washer. Keep the pump in place by securing it to the washer’s frame.
  4. Remove the wire harness from the motor by unplugging it from the side. Remove the screws securing the motor retaining clips with a nutdriver from the top and bottom of the motor. To remove the motor, pry the bottom clip out with the screwdriver. The weight of the motor can be supported by one hand while you remove the top clamp.
  5. When you remove the motor from the bottom of the washer, be sure to expose the drive coupler on the motor as well as the isolator plate and drive coupler on the gearbox. The engine should be placed on a stable surface.
  6. The screwdriver can be used to remove the three-pronged drive coupler from the motor’s back. Remove the spherical isolator plate from the three-pronged coupler on the washer transmission with your hands. Pry the coupler from the transmission shaft with a screwdriver.
  7. A new three-prong drive coupler can now be inserted into the washer’s transmission shaft, as seen in this image. The end of the screwdriver handle should be used to push the coupler all the way onto the transmission shaft of the washer. The new isolator plate should be inserted into the drive coupler prongs.
  8. Reattach the motor shaft with the third and final three-prong driving coupler. Push the coupler against the motor with the handle end of a screwdriver. Open holes in the isolator plate can be used to insert the three prongs of the driver coupler.
  9. To keep the motor in place, use the motor retention clamps. Use the screws you removed before to reattach the clips. Plug the wire harness back into the motor’s side panel.
  10. Place the pump on the motor’s shaft and tighten the screws. Snap the pump retaining clips into place to secure the pump.
  11. Reconnect your washer to the water supply and the electrical outlet by putting it back together.

How to Know When to Replace a Dryer Filter

Keeping your dryer’s lint filter clean is crucial, but did you know that you should also do regular cleaning and maintenance on your dryer filter and vent? Dryer maintenance can help you get the most use out of your machine while also reducing the risk of fire.

Caring for Your Dryer Vent

Take care of your filter now if you haven’t done it recently. Is there any way to tell? You should check your dryer to see if something is obstructing the airflow and causing the drying process to take longer than usual.

How to replace the motor coupler on a top-load washer | Repair guide

Keeping lint out of your dryer exhaust vent is the sole purpose of the dryer filter. If the dryer’s hot air isn’t correctly vented, it can develop buildup in the exhaust vent, which can lead to fires. Ventilation is the first step in caring for the filter. Sears Home Services recommends checking your exhaust vent every two years, if not every year, to make sure there is no buildup.

The more often you do laundry and the larger your family is, the more often you should inspect it. It’s important to keep the vent cap clean and clear of any debris that could impede airflow. Lint and debris are easily removed with this drill-attached dryer vent cleaner kit’s nylon brush. Because it’s available in a variety of lengths ranging from 20 feet to 50 feet, it’s important to choose the right one.

Next Steps in Dryer Filter Maintenance

With a long lint brush or a vacuum cleaner, you may remove lint from your dryer filter. Using a metal lawn cap instead of a plastic one will help to reduce the risk of a fire. Non-return shutter flaps prevent pests from entering the vent and are available in four-inch, five-inch and six-inch sizes in stainless steel.

Move inside and clean the opposite end after checking the inside. Family Handyman recommends turning off the gas, unplugging the dryer, and moving the dryer away from the wall so you can get to the duct. You should be able to remove the duct from the dryer and wipe out any lint that has accumulated inside.

Check the area behind the dryer for extra lint and debris. Lint in the air can be drawn into the dryer intake, which is where the air is generally drawn into the dryer from the back. Use a brush or a vacuum attachment to remove lint, pet hair, and dust from the surface.

Caring for the Vent Filter

Cleaning your vent filter is necessary even if it appears to be dust-free. A buildup of dryer sheets on the filter might make it more difficult for air to get through, making it less efficient. Remove and clean the filter every few months.

You may either hand-wash it or put it in the dishwasher, depending on your preference. Either way, any residue on the mesh should be removed. Remove the filter and use a lint brush or a vacuum extension to clean out the trap.

To avoid fires, it’s best to replace the filter if you notice any visible damage to it. Lint and dust can get into the exhaust, which is what causes the flames. A new screen can be purchased through a hardware store or directly from the manufacturer’s website. As soon as you see that it’s showing signs of wear, you may want to start looking for a replacement. A dryer’s exhaust system wouldn’t be complete without a set of dryer filters.

How to Change a Clutch Assembly on a Maytag Washer

Installing the clutch assembly on your Maytag washing machine is straightforward. During the wash cycle, your washer’s clutch helps transfer it from agitation to spinning. It may be time to replace the clutch assembly if you notice that your clothing retain more water at the conclusion of the wash cycle or that the washtub no longer agitates or spins. The washer pump and transmission must be removed in order to replace the clutch assembly.

  1. Unplug your Maytag washing machine from the power source. Water supply must be shut off If there is any water left in the hose, remove it from the machine and dump it into a bucket.
  2. To free the drain hose from the washer, loosen the hose clip that secures it. Use pliers to squeeze the clamp ends or a clamp screw to loosen the clamp. Disconnect the washer’s hose.
  3. You can remove the top of the agitator by holding the bottom of the agitator cap or fabric softener dispenser with your fingers and pulling it off. To reveal the 7/16-inch agitator bolt, lift the cap or dispenser. You may remove the cap from inside the agitator by grabbing the top of it and pulling it out of the machine.
  4. Make sure the socket extension has a 7/16-inch socket attached to it before using the socket wrench. The agitator’s bottom bolt should be removed. It’s time to remove your agitator from the washing machine.
  5. The washer should be moved to a spacious work space. Back the machine up with an old blanket or a shred of carpet. To see the pump, motor, and transmission of the washer, lower the back of the machine to the floor.
  6. Find the two tension clips that hold the pump to the motor and remove them one by one. Pop the pump’s tension clamps with a flathead screwdriver and wriggle it away from the motor. Keep the pump out of the way by attaching the motor to one of the washer frame supports.
  7. Disconnect the motor’s electrical harness. Disconnect the transmission’s wiring harness from the plastic support clamps. Using a frame support, attach the harness to the other end and keep it out of the way.
  8. This is where you’ll find your three 1/2-inch bolts on the transmission. Remove the bolts with a 1/2-inch socket and socket wrench. Grab the transmission and the engine. Remove the complete assembly from the Maytag washer’s bottom. The agitator shaft and transmission clutch assembly half are now visible. In addition, portions of the washer’s clutch mechanism are visible beneath the washtub.
  9. Slide the thrust washer off the agitator shaft with your fingers to remove it from the clutch assembly. Grab the U-shaped support ring that was underneath the thrust washer with needle-nose pliers. To see the clutch retaining ring, remove the support ring from the shaft.
  10. The retainer ring’s position should be noted. Assemble the flathead screwdriver to pry apart each of these parts. The assembly is now free to be removed from the agitator shaft.
  11. In order to remove the nylon brake cam from the Maytag washtub support bracket, follow these steps. Screwdriver: Slide the flathead screwdriver between c clip and cam’s central metal shaft. Slide the C clip off the shaft with a screwdriver and release the cam.
  12. A clutch assembly kit comes with a new cam that you can remove from the bottom of the washer and install. The new C clip can be used to secure the nylon cam.
  13. Make that the spring within the new clutch assembly is facing downward on your work surface. Snap the new clutch assembly’s notched nylon ring into place using the kit’s included notched nylon ring.
  14. Slide the assembly down the agitator shaft with the spring facing up. Replace the old retainer ring and tighten the assembly. Make use of the original U-shaped support ring by snapping it over the agitator shaft above the retainer ring and snapping it in place. Install a new support ring and thrust washer to replace the old one.
  15. The agitator shaft should be slid through the nylon cam’s center aperture. Adjust the motor and transmission such that the new clutch assembly is flush with the new cam and the new gearbox.
  16. The three bolts you removed before should now be used to reattach the transmission to the washer. Re-attach the pump and motor to their respective sockets. In order to reassemble the washer and link it back to the pipes and electricity, follow the disassembly instructions in reverse.

How to Fix a Weak Clutch on a Washer That Is Not Turning

If your direct-drive washer is still operating, but not spinning or agitating, it’s possible that your clutch has worn out and no longer effective. To get your washer operating again, you’ll need to replace the entire clutch. If you know how to use a socket wrench, a screwdriver, and a pair of pliers, you don’t need a professional to make this repair.

  1. Unplug the washer from the wall outlet and turn off its water supply valves. To access the washer’s drain and water hoses, slide the appliance away from the wall.
  2. Remove the drain hose and disconnect the supply hoses. A bucket should be used to catch any residual water from the hoses. Move the washing machine to a wider place.
  3. To get to the agitator, remove the washing cover. Remove the fabric softener dispenser by pulling up on the lock ring on the bottom of it, if necessary.
  4. You will need to use a flat blade screwdriver to dislodge the agitator cap from the agitator’s top. Look for a dust cap inside the agitator. If necessary, use pliers or your hand to remove the dust cover from the agitator.
  5. A socket extender and a 7/16-inch socket are all you need. Use a socket wrench to attach the extension to the wrench. Remove the agitator by inserting the socket into the socket hole.
  6. Behind the washing, lay down an old blanket. To gain access to the washer’s engine and pump, gently lower the washer’s back onto the blanket.
  7. In order to locate a pump, locate the pump on the motor’s front end. Use a flat-bladed screwdriver to loosen the pump’s grip on the motor. Remove the clamps from the pump by lifting up on the screwdriver blade. Remove the pump from the motor of the washing machine.
  8. Grab the washer motor’s wire harness from the side. Remove the wire harness from the motor and wriggle it about. Removing a wire harness from a gear housing beneath a motor can be done by pulling the wires from the plastic clip on its side.
  9. Replace the 7/16-inch socket with a 1/2-inch socket on the socket wrench. Remove the bolts from the gear housing below the motor to free the motor and housing from the washer.
  10. Pull the motor and gear housing from the washer with your hands to reveal the braking cam and the C-clip that holds it to the washer. In order to remove the brake cam, place your flathead screwdriver in between it and the C-clip. Remove the brake cam from the washer by prying the C-clip off of it. Use the new C-clip to secure the new brake cam from the clutch assembly repair kit onto the washer.
  11. Make sure that the agitator shaft is facing upwards and rests on an old towel. Take hold of the thrush washer at the agitator’s shaft’s bottom end. To see the clutch support ring, lift the thrush washer and slide it off the shaft.
  12. Pull the clutch support ring from the shaft with needle nose pliers to expose the clutch retainer ring. The flat head screwdriver should be inserted between the clutch retaining ring and the retainer. When you remove the washer’s clutch ring, slide it off the agitator shaft to free it.
  13. It comes with your new clutch assembly, so locate it. Nylon ring with four tabs on the outside looks like this. Get a new clutch and insert the isolator into it. The replacement clutch simply snaps into place.
  14. Once it’s resting against the gear housing, you’re ready to install your new clutch. To keep the clutch firmly attached to the gear housing, just insert the replacement retainer ring.
  15. Replace the agitator shaft support retainer ring above the retainer ring with a new one. It’s time to remove the thrush washer and replace it with one that is the same size and shape.
  16. Reinstall the agitator shaft so that it is flush with the bottom of the washer by sliding it back into the washer under the gear housing and motor. The engine and housing may need to be moved to the right or left to get them to sit flush.
  17. Reinstall the gear housing bolts. Afterwards, reconnect the pump and carefully lift the washer to its upright position again. Reverse the remaining disassembly steps to put the washer back together again. Set up your washing machine by re-wiring it and re-connecting the water and drain lines.

How to replace the motor coupler on a top-load washer | Repair guide

How to Install a Motor Coupling on a Washing Machine

A damaged drive coupling on the motor shaft could be the cause of a washing machine that doesn’t agitate or spin. If you’re handy and strong enough to move the washing machine, you can probably replace the coupling yourself. In order to remove the machine’s cover and work on the side where its motor is housed, you’ll need ample space. Before you begin, be certain you have the proper coupling assembly for your machine.

  1. Make sure the machine is unplugged, the drain hoses are unhooked, and the machine is moved away from the wall.
  2. Phillips screwdriver to remove the control panel screws from the machine’s top. There may be screws hidden behind the panel if you can’t find them in front of you Pry off the molding with a flathead screwdriver if they’re buried by molding on the panel’s sides. Pry the panel off with a putty knife if you can’t see any screws or molding.
  3. To remove the control panel, first unplug it from the washing machine and then use a flat-head screwdriver to remove the spring clips holding it in place. The washing machine’s cover can be removed by tilting the top forward and sliding the cover toward you.
  4. The machine’s motor may be found near the bottom of the machine’s side. The water pump must be removed in order to gain access to it. Unsnap the pump clamps with a screwdriver and remove the pump from the motor’s drive shaft.
  5. Unscrew the retaining screws holding the motor to the washing machine and remove the electrical harness. The retaining clips must be removed as well in order to remove the motor. Using a flat-head screwdriver, remove the clamps holding the motor in place. Entirely remove the motor.
  6. Remove the old coupling from the motor drive shaft by removing the three pieces. It’s possible that a screwdriver will be required to remove them. Reinstall the coupling components in the same order.
  7. The outer cog of the connection should be aligned with the isolator on the washing machine, and the motor should be pushed back into place. Install the wiring harness after securing the motor with the retaining clips and screws. Reinstall the clamps that secure the water pump to the driving shaft.
  8. Reverse the process you used to remove the cover off the machine and reinstall the control panel. It’s time to put the washing machine through its paces.

FAQs

How do I know if my washer motor coupler is bad?

if you hear the motor moving but the washer isn’t agitating, turn the spin dial to its highest setting. You may have a faulty motor coupler if you hear the washer’s motor running (making noise but not spinning) while the water drains.

What causes a motor coupler to break?

The most common reason for motor coupler failure is that the washer is either overloaded or there is not enough water available. Possibly causing the motor coupler to break, if the clutch is not sliding and it is giving too much initial torque to the basket drive.

What is a washer motor coupler?

The washing machine motor coupler is a flexible coupling that connects the motor shaft to the direct-drive gearbox of the appliance. To prevent harm to the motor, the connection is broken when the drive system malfunctions.

What is motor coupler?

In an appliance, such as a washing machine, the motor coupler is a mechanism that links an electric motor to the drive system. In most cases, a motor coupler is a three-piece component with two drive plates and a rubber shock absorber between them.

How do I know if my Kenmore transmission is bad?

The lack of agitation is a common indication of a faulty transmission. While the machine continues to spin and drain, the agitator simply does not work while in the agitate mode.

Why is my washer making a humming noise?

The soft humming sound may be generated by a jammed pump trying to turn. The most typical explanation for the pump not working is that a little piece of clothing has been lodged in the pump’s mechanism. The drive block for the washer must be replaced if it is loose or worn out.

What is clutch in washing machine?

Your washing machine has a clutch component (Clutch, Washer Clutch) that spins the basket during the spin cycle. The lining of a clutch bag might become soiled over time. In order to release the brake, the clutch assembly must rotate freely.

How do I know if my agitator is working?

Water should begin to swirl around the agitator, mixing up the garments. The sensor should be depressed if the agitator does not move. If the sensor still doesn’t move the agitator, it’s broken and needs to be fixed.

What is a direct-drive coupling?

These Direct Drive Washer Motor Couplings provide a smooth connection between the gearbox and the motor’s shaft, reducing vibration and noise. It is connected to the motor shaft and the direct-drive transmission. Combo Washer and Dryer.

It’s A Wrap!

Appliances like a washing machine are among the most regularly utilized in households. Coupling difficulties can happen to anyone. This problem can be resolved by familiarizing oneself with the specifics of how to replace the motor connection on a Kenmore washing machine. If you follow these instructions to the letter, you should be able to fix your washer yourself. Hopefully, you’ve learned how to replace a Kenmore washer’s motor coupling. For more information about operating a Kenmore washing machine and how to reset a Kenmore washing machine, please see the following links:

https://homeguides.sfgate.com/install-motor-coupling-washing-machine-61387.html

Helen Skeates

Helen Skeates

Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book. It has survived not only five centuries, but also the leap into electronic typesetting, remaining essentially unchanged. It was popularised in the 1960s with the release of Letraset sheets containing Lorem Ipsum passages, and more recently with desktop publishing software like Aldus PageMaker including versions of Lorem Ipsum.