Maytag Washer Leaks When Filling Up? Things You Should Know!

Helen Skeates
Helen Skeates
14 min read

Maytag washers leak as they are filling, have you noticed? You don’t have to freak out! If your washing machine leaks when filling up, this article will explain why and how to remedy the problem.

In less than an hour, you can fix the washing machine on your own. When it comes to modern household appliances, washers are often overlooked. When the washer leaks, even a slight problem might cause a lot of inconveniences.

When your washing machine leaks, you’ll have to spend a lot of time and effort cleaning up the mess that’s left behind. You can extend the life of your appliance and save money on repairs if you maintain it correctly. Before attempting to repair the washer, you must first determine the source of the problem. When the washer leaks while being filled, there are several possible causes. Many of these factors are covered in the following sections. Let’s get started on this article, shall we?

Why Washer Leaks When Filling Up And Its Repair

You should drain the washer and turn off the appliance for safety’s sake before starting any washer repairs. The reason why your Maytag washer is leaking when it is filling up is now clear. The following are some of the explanations:

Reason #1. Loose pipe connections

One of the most typical reasons for a leak is an improperly connected supply or drain pipe valve. Pull the washer away from the wall to begin the process. When the washer’s backside is exposed, inspect all the connections. Three valves are the most common configuration. In addition to the two valves for the clean water supply, there is a third for the drain. In order to distinguish between hot and cold water, the hoses are marked with red and blue.

Washer Leaking from Bottom. What Should You Do? Same Day Repair

You must tighten the connectors of a clean water supply to prevent a leak while filling the washer. Tighten the connection between the clean water pipes and the washer with your hands to restore it. Replace the gasket if the water supply or drain lines are not reconnected.

Reason #2. Faulty pump

There is no washer without a pump. On the back of the washer, it’s common to find a hose bib, which connects the clean water supply with the drain. If the pipes that are coupled to the pump are secure, the problem is most likely in the pump itself.. Once you’ve located the pump, give it a thorough inspection for any loose or clogged connections. As soon as the drum begins to fill, the water will begin to leak out of the pump. The defective pump must be replaced in this case. Replacement of the malfunctioning washer pump should be done by an expert rather than by yourself.

Reason #3. Damaged air gap

The air gap can cause washer leaking while filling. The washer’s air gap is a small metal device that sits between the washer’s inlet holes. In order to keep the water coming into the washer clean, an air gap has been installed. Additionally, it prevents the water from being diverted to the household’s main water supply. Leaks can be caused by any part of an air gap that is damaged. Because of this, you will need to replace the water supply pipe.

Reason #4. Old gasket

There is a gasket used to keep water from leaking out of the washer drum and into the drum cover. During the spin cycle, a more precise diagnosis can be made. Washer leaks as it spins and dribbles water down into a basin underneath In order to get to the front panel, you will need to empty the water from the washer and turn off the electric supply. After that, remove the washer’s drum. The soapy water stains on the gasket of the drum are an easy way to identify it. Look for signs of wear and deformation on the drum gasket. The gasket must be replaced if it is old and damaged. It is strongly advised that you get an expert to perform this replacement.

Reason #5. The detergent drawer is not in its place

If the detergent drawer isn’t closed properly, the washer can leak. Push the detergent down into the machine after you’ve put it in. The washer will leak if the detergent drawer is not in its proper place. Learn how to properly use laundry detergent pods if it interests you.

Reason #6. Damaged seal of the washer lid

Starting your front-loading washer will cause leaks if the lid is not tightly closed. After repeatedly smashing the top of the washer to no avail, you should take a look at the lid seal. The seal must be replaced if it is damaged.

Water Accumulates on the Floor When Filling the Washing Machine

Nowadays, most houses have a washing machine as a modern convenience. It’s easy to overlook the need for frequent inspection and maintenance on a machine that you use nearly every day without incident, unless something goes wrong. When your washing machine is loading, water may be gathering on the floor for a variety of reasons.

Loose Connections

Inspect the machine’s hot and cold water supply inlet hoses. During the fill cycle, water will leak and pool on the floor if gaskets are missing or connections are loose. Replace any broken or missing gaskets and washers and tighten the connections to halt the leak. In order to avoid leaks, GE Appliances suggests changing the fill hose screens and washers every five years.

Air Gap Device

The air gap, a minor mechanism put by the manufacturer to prevent the washing machine water from being sucked into the household water supply, may be the cause of leakage during the fill cycle. Air gap devices can be found at either end or halfway along the black rubber hose which links the washing machine to the water-inlet valve. The hose must be changed if a component in the air gap is fractured or damaged.

Uneven Washer

It’s possible for water to splash off the top of the basket or load if your washing machine isn’t level. If the washer is tilted too far forward, water may spill out of the tub and onto the floor as it fills. Check the machine’s level by running a level across the front and back of it. Afterwards, position the level on each side of the machine to ensure that the machine is level from top to bottom. Adjust the machine’s feet at the base if necessary if it isn’t level.

Main Tub Seal

In order to prevent water from entering the outer tub and spilling out, a primary tub seal must be installed. Between the washer’s gearbox and the outside tub, this seal is fitted. Repair Clinic says that if it starts to leak, the water will appear in the middle of the outer tub bottom. When the washing machine is full of water, you can open the access panel to inspect the tub seal. A professional should be called if you notice water in the bottom of the outer tub.

What to Do if Your Washing Machine Squeaking?


A drive belt turns the washing machine pump, which normally has two or three black hoses attached to it. It’s common to notice a leak when the tub is filling or is already full of water. For the most part, homeowners should leave pump repairs to the professionals. If the pump has to be repaired or replaced, make an appointment with a mechanic.

My Maytag Washer Leaks During Fill

Hoses/Air Gap

Check the fill hoses on the back of your Maytag washer if it is leaking during the fill cycle. Check to see sure the wires are securing properly. Tighten it if necessary. Check to see that the four fill washers are properly placed. Check to check if the hose is fractured or punctured. The hose has to be repaired or replaced. Older Maytag washing machines have an air gap. This is a plastic device that prevents water from the tub from contaminating your home’s drinking water source. If the device has a crack or is severely deformed, it is better to buy a new one because the damaged part is nearly impossible to repair.


If the washer is leaking during the fill cycle, check to see if it is level. In order to ensure the unit is level from front to back and side to side, you should use a bubble level. As the washer isn’t level, water sprays out of the machine when it rattles. The floor beneath the washing machine should be inspected. Before you buy a new washing machine, check to see if the floor is unsteady. A 3/4-inch piece of plywood can be placed under the washing machine and dryer to keep them level if you can’t replace the floor. If the weight of the washing machine isn’t being distributed evenly, adjust the leveling feet.


An overflowing tub is a common cause of leaks in Maytag washers during the fill stage. It is possible that water entering the tub will splash onto your floor if it bounces off the load. When the agitator is full, remove some clothing and evenly disperse the weight of the mixture. Check to see sure the washing machine’s lid is entirely closed. Dispose of anything sticking out of the tub that can obstruct the lid from shutting entirely.

Water Inlet Valve/Tub Seal

Behind the washing machine is the water inlet valve. A little tube runs through the middle of it. Get a replacement tube if current one is damaged or punctured. If the water in your bathtub is spilling, the inlet valve is broken. If the valve itself is leaking, you need a new one. Near the transmission, the tub seal has a tight fit. It’s time for a replacement seal if it’s cracked or fragile. For assistance, contact a Maytag repair person.


Why does my washer leak while filling?

In the event that your washer leaks while filling, it may be overfilling. Using a pressure-activated switch, the water level switch allows you to precisely control the water level in your bathtub. The switch’s diaphragm will be pushed against the tub’s compressed air as it fills with water.

Why is my Maytag washer leaking from the bottom?

The drain pump is responsible for removing water from the drain pipe. This can occur if the drain pump is damaged or if the bearings have failed. If the drain pump is leaking, you’ll need to get a new one because it can’t be repaired. There may be a tear in the tub seal, allowing water to leak out.

Why would a washing machine leak from underneath?

Water pumps and the hoses that connect to them are frequently the source of leaks under the washer. If the pump is defective, you’ll feel a lot of rumbling or shaking during the wash cycle. A washer’s water pump is often found near the machine’s base.

Washer Leaking from Bottom. What Should You Do? Same Day Repair

Can too much detergent cause washing machine to leak?

Adding too much detergent to your washing machine might potentially cause leaks, rather than damage or breakage to a component. Oversudsing can occur at any point during the washing process, although it is most noticeable when the machine is emptying. If this is the case, use a lower-sudsing detergent.

Will an unlevel washing machine leak?

Because washers are supposed to be used on a flat surface, water can leak out if the washer is not level. If your floor is uneven, the washing legs make it easy to level the appliance. No more than 8 pounds of garments or blankets should be in your washing machine. Water can leak if the system is overburdened.

It’s A Wrap!

Your Maytag washer leaks while full, and now you know why. As with other device, the washer is susceptible to a variety of problems. Understanding and diagnosing the problem are crucial. If you’ve read this far, you’ve probably figured out why your washer leaks when it’s filling. Every five years, it’s a good idea to replace all of the washer’s hoses and seals to ensure that it will last for many years to come. Leaks, for example, can be avoided entirely with regular maintenance. Know how to reset my Maytag washer and what LE on an LG washer implies by reading related topics.

Helen Skeates

Helen Skeates

Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book. It has survived not only five centuries, but also the leap into electronic typesetting, remaining essentially unchanged. It was popularised in the 1960s with the release of Letraset sheets containing Lorem Ipsum passages, and more recently with desktop publishing software like Aldus PageMaker including versions of Lorem Ipsum.